(954) 718-3094 Request an estimate

Martin County, Florida

Impact Windows and Doors in Martin County

Hurricane-rated windows and doors set into properly repaired concrete openings.

In short

Who handles impact windows and doors in Martin?

SERPE-CO replaces impact windows and doors in Martin County for condominium associations and commercial property owners. On each job we survey and measure every opening, submit Florida product approvals with the permit, take out the old units, repair the concrete and stucco around the openings and anchor the new units with stainless steel fasteners, each one surrounded by urethane hybrid sealant, then seal the perimeter.

Free milestone planner

Is a milestone inspection coming due on your building?

Enter the year your building got its certificate of occupancy and how many stories it has. The planner estimates your deadline under Florida law, then you can send it to SERPE-CO for a second look.

Building type

Add the year and story count for an estimated due date.

About this estimate

This is a planning estimate drawn from the statewide rule in Florida Statute 553.899. Your local building department sets the real deadline and may call for the first inspection at 25 years instead. Broward County also has its own Building Safety Inspection Program. Check your date with your building official and engineer, or contact SERPE-CO and we will help you sort it out.

Impact Windows & Doors · Martin

Impact windows and doors in Martin County are chosen from the Florida product approval system, matched to the design pressures an engineer sets for each opening and installed under permit from the city, town or county building office. Only Miami-Dade and Broward fall within the High-Velocity Hurricane Zone, so Martin sits outside it. SERPE-CO handles window, slider, storefront and entry replacement on multi-story condominiums and commercial buildings, including the concrete and stucco repairs around each opening.

Every fastener we drive is stainless steel, and every one is surrounded by urethane hybrid sealant, so the screw is never in direct contact with the concrete. Ordinary screws rust in coastal concrete that stays damp and salty, and rust takes up more room than steel, which splits the concrete holding the frame. Sealing the fastener keeps water out of that path and away from the reinforcing steel. The detail adds time at each opening, and SERPE-CO does not skip it.

Brett Serpe, MBA, GC, CEO of SERPE-CO

Reviewed by Brett Serpe, MBA, GC, CEO of SERPE-CO · Florida Certified General Contractor CGC #1523974

Prepared by the SERPE-CO project team, with more than 20 years in concrete restoration. Last reviewed November 2026.

Impact windows and doors in Martin County by SERPE-CO
Martin County coastal condominium buildings

Local conditions

What governs an opening replacement in Martin

Products installed here carry a Florida product approval, listed through the Florida Building Commission, that states the sizes, design pressures and installation details the unit was tested for. The building department reviews those approvals with the permit, and Martin County permit forms reference the 8th Edition (2023) Florida Building Code. On tall oceanfront buildings, some engineers specify HVHZ-approved products as a matter of preference, even though Martin is outside that zone.

Exposure along the water sets the details. Condominiums on the Martin County end of Hutchinson Island and on Jupiter Island face open ocean with broad sliders and corner glass. Buildings along the St. Lucie River in Stuart, around Sewall's Point and beside the Indian River Lagoon in Jensen Beach take humid, brackish air that corrodes aluminum frames and the anchors under them. Inland offices and retail buildings in Palm City and along US 1 have storefronts and entries that need the same care.

Buildings that need this work

Martin buildings and the openings we replace

On Hutchinson Island and Jupiter Island, oceanfront condominiums have the largest glass in the county: sliding doors across the full width of a unit, corner windows that wrap two walls and lobby entries facing the beach. Design pressures differ from floor to floor and from the middle of a wall to its corners, so an engineer assigns a pressure to each opening, and a single stack can call for two or three products. Original aluminum frames on these buildings often show pitted tracks and corroded anchors.

On the mainland the openings get smaller and more varied. Riverfront condominiums in Stuart and Palm City, lagoon-side buildings in Jensen Beach and Sewall's Point and low-rise communities in Hobe Sound have unit entry doors on walkways, single-hung and awning windows and sliders to screened balconies, often set in stucco over block. Commercial work covers storefronts and entries in historic downtown Stuart, offices along US 1 and Kanner Highway and service buildings in Palm City. Boards with older accordion or roll-down shutters often decide at the same time whether to keep them.

Have a question about your building?Call the office or send a quick request. A real person answers.

The work

Impact windows and doors in Martin County: what the job covers

  1. 01Installing impact windows and sliding glass doors
  2. 02Common-area entries and storefront systems
  3. 03Repairs to sills, jambs and headers
  4. 04Perimeter sealants and waterproofing
  5. 05Stucco and finishes restored around each opening
  6. 06Phased building-wide replacement for associations
Impact Windows & Doors work underway in Martin County

Our approach

Our install sequence on Martin buildings

A crew measures each opening in the field, and those sizes go into shop drawings submitted with the product approvals for the permit. When a unit comes out, we check the concrete and stucco around the opening, repair any spalls or cracks and let the repair cure before the new frame is set. Anchors go in at the spacing and edge distance the approval calls for, each one stainless and sealed. Openings are closed every evening.

Owners hear in advance which day their unit is scheduled and what to move away from the windows. Interior floors along the path are covered, and dust barriers go up at each opening. Once the frame is anchored, the perimeter joint is sealed, the threshold is tied into any balcony waterproofing and finishes inside and out are restored. The office that issued the permit inspects the work, and when a storm is forecast the crew secures open work before leaving.

SERPE-CO brings more than 20 years in the field to every job. Read about our full impact windows & doors service or browse all our work in Martin County.

Planning ahead

Planning an opening replacement across a Martin building

Responsibility comes first. The declaration and bylaws decide whether the association or individual owners are responsible for the windows and doors, and that shapes who signs the contract. A board doing the whole building then adopts a single specification for frame color, glass and product line. After every opening is measured, products are chosen from Florida approvals rated for the engineer's pressures, and the permit goes to the City of Stuart, a town office or the Martin County Building Department, depending on the address.

Factory lead time sets the start date, since units are built only after the permit drawings are approved. Boards often try to schedule the bulk of installation outside the June 1 to November 30 hurricane season, and any work inside it follows a daily close-up rule and stops for tropical systems. Pairing opening replacement with milestone repairs or repainting means residents live with scaffolding and disruption once. When the association maintains the windows and exterior doors, they are part of what the structural integrity reserve study has to cover.

How we run a job

Site walk first, closed permit last.

  1. 01

    Meet on site

    Each job starts on site, walking the property and its conditions with your manager, board or engineer.

  2. 02

    Follow the engineer's scope

    The engineer writes the scope. We price it line by line, plan access and lay out each phase to build it.

  3. 03

    Put safety first

    We can never work too safely: shoring, swing stages, barricades and notices go up first.

  4. 04

    Build the repairs

    Crews work through the repairs in order, stopping for inspections wherever the engineer calls for them.

  5. 05

    Finish and document

    Final inspections, a closed permit and a full record of the work for the association.

Ready for a site visit?Tell us where the building is and what you are seeing. We will set up a time to walk it.

Cities served

Impact Windows & Doors throughout Martin County

Summary

What Martin boards and owners should remember

  • 01

    Martin County is outside the High-Velocity Hurricane Zone, and impact units need a Florida product approval rated for each opening's design pressure.

  • 02

    Martin County permit forms reference the 8th Edition (2023) Florida Building Code for this work.

  • 03

    Every SERPE-CO anchor is a stainless steel fastener with urethane hybrid sealant around it, so no screw touches bare concrete.

  • 04

    The condominium documents decide whether windows and doors are an association or owner responsibility.

Questions

Impact Windows & Doors in Martin: questions we hear

Does a Jupiter Island building need Miami-Dade-rated windows?

Not by code. The High-Velocity Hurricane Zone covers Miami-Dade and Broward only, and Martin County sits outside it. Each unit has to carry a Florida approval that meets the design pressure the engineer calculates for its opening. Where an oceanfront wall takes heavy exposure, some engineers pick HVHZ-approved products anyway, and a board can follow that advice, but the code in Martin does not demand it.

What does the sealant around each fastener actually do?

Urethane hybrid sealant fills the space around every stainless steel fastener, so the screw is isolated from the concrete and water cannot run along it. Concrete near salt water stays damp, and unprotected screws in it corrode and crack the sill or jamb. Sealing each fastener protects the anchor, the frame and the steel inside the wall for the life of the installation.

Should a Stuart condominium replace windows before repainting?

Usually yes, or as part of the same project. Window replacement disturbs the stucco and paint around every opening, and repainting afterward covers the patches and gives the building one consistent finish. Paint is also the waterproofing layer on a stucco wall, so new frames and a fresh coating together close the paths water uses to get inside.

Why can two units on the same Hutchinson Island stack need different windows?

Wind pressure on a building is not uniform. An engineer calculates the design pressure at each opening, and the numbers rise toward the top floors and the corners. Each Florida product approval lists the pressures and sizes it covers, so each unit gets a product whose approval meets or exceeds the figure for its opening, anchored the way that approval requires.

Can a Hobe Sound owner install impact windows on their own?

That depends on the condominium documents and the association's rules. Many boards allow owner replacements only to the building specification, so the facade matches and the perimeter seal is the same at every unit. Each replacement needs a permit from the Martin County Building Department for unincorporated Hobe Sound, along with the product approval for that unit.

What is the timeline for a building-wide window project in Martin?

For impact windows and doors in Martin County the longest phase is preconstruction: the opening survey, the engineer's pressures, shop drawings, permit review and manufacturing. Installation then runs stack by stack at a steady daily pace, and every owner gets a calendar showing when crews will be in their unit, so nobody is caught off guard.

Laws and rules cited

Treat this page as general information only, not legal or engineering advice. Licensed engineers and architects perform the inspections, and the building official decides which dates apply to your property. SERPE-CO's role is to carry out the repairs.

Working with an engineer?

Holding drawings, specifications or a complete set of bid documents?

Structural engineers, property engineers and board members send SERPE-CO much of our restoration, pool and roofing work. Once a scope has been drawn and specified, our team prices what the documents show, raises questions where something is unclear, and lays out each line so boards can weigh the bids on equal terms.

Request an estimate

Let's plan your restoration.

Tell us where the building is and what you are seeing. We set up a visit to the property, then send a written proposal, or tell you an engineer needs to write the scope first.

  • More than 20 years in the field
  • St. Lucie, Martin, Palm Beach, Broward and Miami-Dade
  • Family-owned Certified General Contractor

Rather call?(954) 718-3094

Work needed (choose all that apply)
Call Request an estimate