(954) 718-3094 Request an estimate

St. Lucie County, Florida

Impact Windows and Doors in St. Lucie County

Hurricane-rated windows and doors set into properly repaired concrete openings.

In short

Who handles impact windows and doors in St. Lucie?

SERPE-CO installs impact windows and doors in St. Lucie County for condominium associations and commercial owners. The job covers measuring each opening, submitting Florida product approvals with the permit, removing the old frames, repairing the concrete and stucco at every opening, and anchoring each new unit on stainless steel fasteners with urethane hybrid sealant around every fastener before the perimeter is sealed.

Free milestone planner

Is a milestone inspection coming due on your building?

Enter the year your building got its certificate of occupancy and how many stories it has. The planner estimates your deadline under Florida law, then you can send it to SERPE-CO for a second look.

Building type

Add the year and story count for an estimated due date.

About this estimate

This is a planning estimate drawn from the statewide rule in Florida Statute 553.899. Your local building department sets the real deadline and may call for the first inspection at 25 years instead. Broward County also has its own Building Safety Inspection Program. Check your date with your building official and engineer, or contact SERPE-CO and we will help you sort it out.

Impact Windows & Doors · St. Lucie

Impact windows and doors in St. Lucie County need a Florida product approval rated for the design pressures of the building they go in. St. Lucie is outside the High-Velocity Hurricane Zone, which covers only Miami-Dade and Broward, so the statewide approval system applies here. SERPE-CO replaces windows, balcony sliders, storefronts and lobby entries on condo and commercial buildings, and our crews repair the concrete and stucco around each opening before a new frame goes in.

The part owners never see is the anchoring. SERPE-CO sets every frame with stainless steel fasteners and puts urethane hybrid sealant around every fastener, so no screw touches bare concrete. Carbon steel screws in damp, salty concrete rust and swell, and the expanding rust cracks the jamb or sill they were holding. Keeping water off each fastener protects the screw, the frame and the reinforcing steel in the wall, and that care matters most on buildings facing the ocean or the lagoon.

Brett Serpe, MBA, GC, CEO of SERPE-CO

Reviewed by Brett Serpe, MBA, GC, CEO of SERPE-CO · Florida Certified General Contractor CGC #1523974

Prepared by the SERPE-CO project team, with more than 20 years in concrete restoration. Last reviewed November 2026.

Impact windows and doors in St. Lucie County by SERPE-CO
St. Lucie County coastal condominium buildings

Local conditions

Product approvals and exposure in St. Lucie

Florida product approval is a statewide system run through the Florida Building Commission. Each approved window, door or storefront system lists the sizes, design pressures and installation method it was tested for, and the building official reviews those approvals with the permit. Some engineers specify HVHZ-approved products even though St. Lucie is outside that zone, particularly on tall oceanfront walls, and that is a choice for the design team rather than a requirement here.

Exposure varies across the county. Oceanfront condominiums along A1A on Hutchinson Island have full-width balcony sliders and corner glass facing the Atlantic, with the lagoon behind them. Lagoon-front buildings in Fort Pierce and St. Lucie Village take brackish air and spray off the water near the inlet. Inland in Port St. Lucie, mid-rise and commercial buildings along US 1 and in St. Lucie West and Tradition have storefronts, entries and older aluminum windows set in stucco over block.

Buildings that need this work

Openings we replace on St. Lucie buildings

Hutchinson Island towers have the biggest and most exposed openings in the county: sliders spanning the width of a unit, tall fixed glass at the corners and lobby storefronts that face the beach or the pool deck. An engineer works out the design pressure for each opening, and the result changes with height and with position on the building, so upper corner units on one stack may need a different product than lower floors. Buildings along the lagoon in Fort Pierce and St. Lucie Village have a similar mix of sliders, fixed panes and entries.

Port St. Lucie brings a different set. Low-rise and mid-rise condominiums have original single-hung or awning windows, unit entry doors on open walkways and sliders to small screened balconies, all set in stucco over concrete block. Commercial openings include storefronts and entries at retail centers on US 1 and Port St. Lucie Boulevard, offices in St. Lucie West and Tradition, and service buildings across the city. Older shutters are usually part of the conversation, since a board replacing glass often decides at the same time whether to keep, repair or remove them.

Have a question about your building?Call the office or send a quick request. A real person answers.

The work

Impact windows and doors in St. Lucie County: what the job covers

  1. 01Installing impact windows and sliding glass doors
  2. 02Common-area entries and storefront systems
  3. 03Repairs to sills, jambs and headers
  4. 04Perimeter sealants and waterproofing
  5. 05Stucco and finishes restored around each opening
  6. 06Phased building-wide replacement for associations
Impact Windows & Doors work underway in St. Lucie County

Our approach

How we replace openings in an occupied St. Lucie building

Our crew field measures each opening, because actual sizes rarely match the original plans exactly. Shop drawings and the product approvals are submitted for the permit. When install day comes, the old frame comes out, the opening is checked for spalled concrete or damaged bucks, and repairs are finished before the new unit is set and anchored. No opening is left uncovered at the end of the day, and work stops early when a storm is forecast.

Residents receive a schedule by floor and stack, with simple instructions to clear blinds and furniture from the openings. Floors along the route are protected. Once each frame is anchored, our crew seals the perimeter, joins the sill to the balcony membrane where one exists and patches the finishes inside and out. The building department of the county, Port St. Lucie or Fort Pierce, whichever issued the permit, inspects the installation.

SERPE-CO brings more than 20 years in the field to every job. Read about our full impact windows & doors service or browse all our work in St. Lucie County.

Planning ahead

Planning a building-wide replacement in St. Lucie

The condominium documents come first, because they say who answers for the openings, the association or each owner. The board then adopts one specification for product line, frame finish and glass so the building looks uniform and every unit gets the same perimeter detail. Every opening is surveyed, product approvals are matched to the engineer's design pressures, and the permit goes to the right office for the address: St. Lucie County, Port St. Lucie or Fort Pierce. On Hutchinson Island that office depends on where the building sits.

Manufacturing begins only after the permit drawings are accepted, so purchase orders go in well ahead of the first install day. Hurricane season runs June 1 to November 30, and crews plan to close every opening each day and pause when a tropical system threatens. Many St. Lucie boards line up opening replacement with milestone repairs or repainting so the building goes under swing stage once. Windows and exterior doors also belong in the structural integrity reserve study where the association is responsible for them.

How we run a job

Site walk first, closed permit last.

  1. 01

    Meet on site

    Each job starts on site, walking the property and its conditions with your manager, board or engineer.

  2. 02

    Follow the engineer's scope

    The engineer writes the scope. We price it line by line, plan access and lay out each phase to build it.

  3. 03

    Put safety first

    We can never work too safely: shoring, swing stages, barricades and notices go up first.

  4. 04

    Build the repairs

    Crews work through the repairs in order, stopping for inspections wherever the engineer calls for them.

  5. 05

    Finish and document

    Final inspections, a closed permit and a full record of the work for the association.

Ready for a site visit?Tell us where the building is and what you are seeing. We will set up a time to walk it.

Cities served

Impact Windows & Doors throughout St. Lucie County

Summary

What St. Lucie boards and owners should remember

  • 01

    St. Lucie is outside the High-Velocity Hurricane Zone, so impact units need Florida product approval matched to the design pressures of the building.

  • 02

    The building official reviews product approvals with the permit, so each opening is matched to its approval before work starts.

  • 03

    SERPE-CO anchors every unit on stainless steel fasteners with urethane hybrid sealant around each fastener.

  • 04

    Upper floors and corners of Hutchinson Island towers can call for higher-rated products than the lower floors.

Questions

Impact Windows & Doors in St. Lucie: questions we hear

Do impact windows in St. Lucie need a Miami-Dade NOA?

No. St. Lucie is outside the High-Velocity Hurricane Zone, which applies only in Miami-Dade and Broward. Units here need a Florida product approval rated for the design pressures at each opening, and the anchoring must follow that approval. Some engineers still choose HVHZ-approved products for exposed oceanfront walls, which is a specification decision rather than a code requirement in this county.

Why does SERPE-CO seal around every fastener?

Coastal concrete holds moisture and salt. A plain steel screw driven into it corrodes, and the rust expands and cracks the concrete around the frame. SERPE-CO uses stainless steel fasteners with urethane hybrid sealant around each one, so the screw never sits against bare concrete and water cannot travel along it into the wall and reach the reinforcing steel.

Should a Hutchinson Island condominium replace windows during its milestone repairs?

Often that is the efficient order. Milestone work can rebuild slab edges, balcony thresholds and the concrete around openings, and a new door sill has to tie into the repaired balcony and its waterproofing. Coordinating both projects avoids setting new doors that then sit beside chipping hammers for weeks. The engineer and the board decide the final sequence together.

How long does a window replacement take in a Fort Pierce condominium?

Most of the calendar passes before any frame comes out: measuring, shop drawings, permit review and factory production. After delivery, crews work through a set number of openings per day, stack by stack, so the installation itself moves steadily. Owners get a unit-by-unit calendar ahead of time and know which day to expect the crew.

Can a Port St. Lucie owner replace windows separately from the rest of the building?

The condominium documents decide. Many associations allow owner replacements only when they follow the building specification for product, color and installation, so the exterior stays consistent and the waterproofing detail matches from unit to unit. Each replacement still needs its own permit through the City of Port St. Lucie, with a product approval for the opening.

What should a St. Lucie board settle before choosing a product?

Ask the engineer for the design pressure at each opening first. Products are then chosen from Florida approvals rated at or above those figures, in sizes that fit the surveyed openings. For impact windows and doors in St. Lucie County, SERPE-CO then plans the anchoring each approval calls for and repairs the concrete those anchors will go into.

Laws and rules cited

Treat this page as general information only, not legal or engineering advice. Licensed engineers and architects perform the inspections, and the building official decides which dates apply to your property. SERPE-CO's role is to carry out the repairs.

Working with an engineer?

Holding drawings, specifications or a complete set of bid documents?

Structural engineers, property engineers and board members send SERPE-CO much of our restoration, pool and roofing work. Once a scope has been drawn and specified, our team prices what the documents show, raises questions where something is unclear, and lays out each line so boards can weigh the bids on equal terms.

Request an estimate

Let's plan your restoration.

Tell us where the building is and what you are seeing. We set up a visit to the property, then send a written proposal, or tell you an engineer needs to write the scope first.

  • More than 20 years in the field
  • St. Lucie, Martin, Palm Beach, Broward and Miami-Dade
  • Family-owned Certified General Contractor

Rather call?(954) 718-3094

Work needed (choose all that apply)
Call Request an estimate